Buying a used car is usually a pain in the rear, simply because of the fact that there are so many things that can be wrong with the car. It could be a bad transmission, alternator, carburetor, fuel injector, or any one of a thousand problems that could make you not want a vehicle. Some people buy cars that are “fixer-uppers” simply because of the fact that they are a cheaper buy if they decide to just repair the vehicle on their own. This is typical of mechanics who need a new vehicle, because a lot of the cost of repairing a vehicle comes from paying for the labor, not the actual parts itself.
But, what about water damaged vehicles? Most people do not think about this when they go to buy a vehicle, so they are not sure what to look for.
The first thing you should probably do is smell the interior. You should smell next to nothing. If the smell is a musty odor, then that probably means that mold is growing somewhere inside the vehicle. This could be due to liquid spills inside the car like soda, but it could also be due to the car having been flooded. Look for other signs of water damage if you detect a musty odor. Your prospective vehicle should NOT have been treated with air freshener. This is typically used to cover up musty odors and the dealer you are buying from may be hiding something.
Checking the car’s trunk for buildup of silt, rust, or mud is also a good idea. The area around the taillights should be checked thoroughly, since this is an area where these things will build up most often.
You can get a vehicle history report from a site like Carfax.com, but these are not always reliable. An accident or an incident of flooding will only be on this report if an insurance claim was filed. If the car is in an accident and the insurance company the person is with is not notified, then the incident will not appear on the history report.
Check the electronic parts of the vehicle such as gauges and make sure they are in working order. This can include the fuel gauge and other various indicator lights. Wires in the dashboard and under the steering wheel can be flexed and if they crack, they have probably been exposed to water.
Jim Corkern is a writer and respected contributor to the Water damage restoration and mold remediation Industry. Visit his sites for more information.
http://www.localrestoration.com and
http://www.moldrestorationusa.com
Friday, September 28, 2007
Avoid a Water Damaged Vehicle
Buying a used car is usually a pain in the rear, simply because of the fact that there are so many things that can be wrong with the car. It could be a bad transmission, alternator, carburetor, fuel injector, or any one of a thousand problems that could make you not want a vehicle. Some people buy cars that are “fixer-uppers” simply because of the fact that they are a cheaper buy if they decide to just repair the vehicle on their own. This is typical of mechanics who need a new vehicle, because a lot of the cost of repairing a vehicle comes from paying for the labor, not the actual parts itself.
But, what about water damaged vehicles? Most people do not think about this when they go to buy a vehicle, so they are not sure what to look for.
The first thing you should probably do is smell the interior. You should smell next to nothing. If the smell is a musty odor, then that probably means that mold is growing somewhere inside the vehicle. This could be due to liquid spills inside the car like soda, but it could also be due to the car having been flooded. Look for other signs of water damage if you detect a musty odor. Your prospective vehicle should NOT have been treated with air freshener. This is typically used to cover up musty odors and the dealer you are buying from may be hiding something.
Checking the car’s trunk for buildup of silt, rust, or mud is also a good idea. The area around the taillights should be checked thoroughly, since this is an area where these things will build up most often.
You can get a vehicle history report from a site like Carfax.com, but these are not always reliable. An accident or an incident of flooding will only be on this report if an insurance claim was filed. If the car is in an accident and the insurance company the person is with is not notified, then the incident will not appear on the history report.
Check the electronic parts of the vehicle such as gauges and make sure they are in working order. This can include the fuel gauge and other various indicator lights. Wires in the dashboard and under the steering wheel can be flexed and if they crack, they have probably been exposed to water.
Jim Corkern is a writer and promoter of quality
water damage restoration companies and
mold remediation companies across the united states.
But, what about water damaged vehicles? Most people do not think about this when they go to buy a vehicle, so they are not sure what to look for.
The first thing you should probably do is smell the interior. You should smell next to nothing. If the smell is a musty odor, then that probably means that mold is growing somewhere inside the vehicle. This could be due to liquid spills inside the car like soda, but it could also be due to the car having been flooded. Look for other signs of water damage if you detect a musty odor. Your prospective vehicle should NOT have been treated with air freshener. This is typically used to cover up musty odors and the dealer you are buying from may be hiding something.
Checking the car’s trunk for buildup of silt, rust, or mud is also a good idea. The area around the taillights should be checked thoroughly, since this is an area where these things will build up most often.
You can get a vehicle history report from a site like Carfax.com, but these are not always reliable. An accident or an incident of flooding will only be on this report if an insurance claim was filed. If the car is in an accident and the insurance company the person is with is not notified, then the incident will not appear on the history report.
Check the electronic parts of the vehicle such as gauges and make sure they are in working order. This can include the fuel gauge and other various indicator lights. Wires in the dashboard and under the steering wheel can be flexed and if they crack, they have probably been exposed to water.
Jim Corkern is a writer and promoter of quality
water damage restoration companies and
mold remediation companies across the united states.
Water Safety and Sanitation During Hurricanes
When you are preparing for a hurricane to hit your home and you plan on staying there instead of evacuating, the most important thing that you need to worry about is your water supply. Even though water damage to your home after the storm is over can be a real headache to have to deal with, the water damage that contaminated sea and sewer water can do to you and your family is even more dangerous. You might be able to repair the water damage to your home with money, but drinking or coming into contact with contaminated water can lead to serious illness and even death in some cases.
You should have a large amount of bottled water on hand at any given time if you live in a flood or hurricane prone area. The number of gallons that you have on hand should be enough for every person with you to have one gallon of water a day for at least a week or two. Keeping water purification tablets on hand is one very important thing that will help you if you happen to run out of bottled water for any reason. Chlorinated bleach can also be used to purify any of the contaminated water that you come across. If the water is cloudy, you can filter it through cloth until it is mostly clear. After that, you can use about 1/8 of a teaspoon of chlorinated bleach to treat a gallon of water. Leave this for at least 30 minutes before you attempt to drink it. This will make sure that all the bacteria and viruses in the water have been killed.
Unfortunately, you cannot trust that the water that comes out of your faucet during a hurricane is safe to drink. Flood waters from the sea and from the sewers can contaminate your local water treatment plants and cause the water in them to become undrinkable. You should never drink tap water until your local government assures you that it is safe to drink.
If you have children in your home, do not let them play outside in flood waters. Even if it gets up into the 80’s and 90’s in temperature, the worst thing that you could do is let the kids play in the water, especially young ones that do not know any better than to drink it. Toys that come into contact with the water need to be disinfected with bleach or other chemicals, but this is only for non-porous toys. Stuffed animals and other items like this must be thrown away immediately.
Jim Corkern is a writer and promoter of quality
water damage restoration and
mold remediation companies across the united states.
You should have a large amount of bottled water on hand at any given time if you live in a flood or hurricane prone area. The number of gallons that you have on hand should be enough for every person with you to have one gallon of water a day for at least a week or two. Keeping water purification tablets on hand is one very important thing that will help you if you happen to run out of bottled water for any reason. Chlorinated bleach can also be used to purify any of the contaminated water that you come across. If the water is cloudy, you can filter it through cloth until it is mostly clear. After that, you can use about 1/8 of a teaspoon of chlorinated bleach to treat a gallon of water. Leave this for at least 30 minutes before you attempt to drink it. This will make sure that all the bacteria and viruses in the water have been killed.
Unfortunately, you cannot trust that the water that comes out of your faucet during a hurricane is safe to drink. Flood waters from the sea and from the sewers can contaminate your local water treatment plants and cause the water in them to become undrinkable. You should never drink tap water until your local government assures you that it is safe to drink.
If you have children in your home, do not let them play outside in flood waters. Even if it gets up into the 80’s and 90’s in temperature, the worst thing that you could do is let the kids play in the water, especially young ones that do not know any better than to drink it. Toys that come into contact with the water need to be disinfected with bleach or other chemicals, but this is only for non-porous toys. Stuffed animals and other items like this must be thrown away immediately.
Jim Corkern is a writer and promoter of quality
water damage restoration and
mold remediation companies across the united states.
Smoke Damage Cleanup
Cleaning up smoke damage after a fire can be a pretty involved task, but if you know what you are doing and follow a few simple rules, it might not be as difficult as you might think. Even though you might want to get the job done as quickly as possible, you might end up doing more harm than good if you do not take your time to do it correctly. Do the job right, not rushed.
If you have pets, the best thing for them is to remove them from the area as soon as possible. You need to keep your pets out of the home until you are done cleaning up the smoke and water damage done to the home after the fire trucks have gone. Birds are especially sensitive to smoke and chemicals in the air, so if you had a pet bird in the home at the time of the fire, you should have it examined by a vet.
Use a vacuum cleaner to clean up any soot and other particles from your furniture and floors, after you are certain that the electrical circuitry in the home was not damaged by the water poured into the home by the fire truck.
Plants should be rinsed with water as soon as possible, but be sure not to drown the plant’s soil in an excess amount of water. If the soil has been saturated by the water from the fire truck and you want to save the plant, the best thing to do is to put it in a new pot with new soil.
Open the windows and doors in your home so air can circulate and help remove all the particles from the air inside. This will help remove the smell of smoke from the home, as well.
Do not sit down on upholstered furniture that has not been cleaned yet. This will only rub the soot down into the fabric and make it more difficult to remove.
Sending your clothes to an ordinary dry cleaner can irreparably damage your clothes.
Do not eat any foods that were in the home at the time of the fire. This includes everything that was in the home, no matter what it is. Replace everything in the home that was edible.
Ceilings and walls that have been smoke damaged can sometimes be cleaned and restored to their former selves, but heavier deposits of smoke must be specially treated so that the surface will accept being painted over again. Sometimes the stains cannot be removed and the surface must be painted.
Jim Corkern is a writer and promoter of quality
Connecticut Mold Remediation services and
flood and water damage cleanup companies across the united states.
If you have pets, the best thing for them is to remove them from the area as soon as possible. You need to keep your pets out of the home until you are done cleaning up the smoke and water damage done to the home after the fire trucks have gone. Birds are especially sensitive to smoke and chemicals in the air, so if you had a pet bird in the home at the time of the fire, you should have it examined by a vet.
Use a vacuum cleaner to clean up any soot and other particles from your furniture and floors, after you are certain that the electrical circuitry in the home was not damaged by the water poured into the home by the fire truck.
Plants should be rinsed with water as soon as possible, but be sure not to drown the plant’s soil in an excess amount of water. If the soil has been saturated by the water from the fire truck and you want to save the plant, the best thing to do is to put it in a new pot with new soil.
Open the windows and doors in your home so air can circulate and help remove all the particles from the air inside. This will help remove the smell of smoke from the home, as well.
Do not sit down on upholstered furniture that has not been cleaned yet. This will only rub the soot down into the fabric and make it more difficult to remove.
Sending your clothes to an ordinary dry cleaner can irreparably damage your clothes.
Do not eat any foods that were in the home at the time of the fire. This includes everything that was in the home, no matter what it is. Replace everything in the home that was edible.
Ceilings and walls that have been smoke damaged can sometimes be cleaned and restored to their former selves, but heavier deposits of smoke must be specially treated so that the surface will accept being painted over again. Sometimes the stains cannot be removed and the surface must be painted.
Jim Corkern is a writer and promoter of quality
Connecticut Mold Remediation services and
flood and water damage cleanup companies across the united states.
Hurricane Preparations and Water Safety
There are quite a few things that you need to do if you are preparing for a hurricane to hit your area and you do not want to leave your home, but perhaps the most important thing is making sure that you have a sizeable supply of bottled water in your home. This should be proportional to the number of people living in your home at the time of the storm.
The safety of the water that you will be drinking while the storm is raging outside and even after the storm is gone is important to your survival. You should keep around at least one gallon of water per person per day. Never assume that the water that comes out of your faucet is clean, because water from the sea and possibly from sewers can contaminate water treatment plants in your area. This contaminated water will make you extremely sick and could even possibly lead to death. During a hurricane or a flood, never drink anything but bottled water. Water purification tablets should also be kept on hand and chlorinated bleach can also be used to purify water in most situations. 8 drops per gallon of contaminated water should be enough. Let the treated water set for at least 30 minutes before drinking it.
While water damage to your home may be an important issue after the flood waters have receded, water damage to your body due to contaminated water is even more important. Even if you are not drinking the contaminated water, it can still cause damage to your system, especially if you have open cuts or wounds that have been exposed to it. Wash these with soap and bottled (or chlorine bleach treated) water to keep them from becoming infected.
Children should not be allowed to play in flood waters, no matter how hot it might get inside the home you are staying in. If there are toys that have come into contact with contaminated water, these need to be disinfected before allowing a child to play with them, as well. The hands of children should also be washed very thoroughly often and especially before meals.
Boarding up your windows and doors with plywood is a good idea to keep your windows from being blown out and the glass sent flying into your home and possibly into you.
Jim Corkern is a writer and promoter of quality
damage restoration companies and
mold removal companies across the united states.
The safety of the water that you will be drinking while the storm is raging outside and even after the storm is gone is important to your survival. You should keep around at least one gallon of water per person per day. Never assume that the water that comes out of your faucet is clean, because water from the sea and possibly from sewers can contaminate water treatment plants in your area. This contaminated water will make you extremely sick and could even possibly lead to death. During a hurricane or a flood, never drink anything but bottled water. Water purification tablets should also be kept on hand and chlorinated bleach can also be used to purify water in most situations. 8 drops per gallon of contaminated water should be enough. Let the treated water set for at least 30 minutes before drinking it.
While water damage to your home may be an important issue after the flood waters have receded, water damage to your body due to contaminated water is even more important. Even if you are not drinking the contaminated water, it can still cause damage to your system, especially if you have open cuts or wounds that have been exposed to it. Wash these with soap and bottled (or chlorine bleach treated) water to keep them from becoming infected.
Children should not be allowed to play in flood waters, no matter how hot it might get inside the home you are staying in. If there are toys that have come into contact with contaminated water, these need to be disinfected before allowing a child to play with them, as well. The hands of children should also be washed very thoroughly often and especially before meals.
Boarding up your windows and doors with plywood is a good idea to keep your windows from being blown out and the glass sent flying into your home and possibly into you.
Jim Corkern is a writer and promoter of quality
damage restoration companies and
mold removal companies across the united states.
Tuesday, September 11, 2007
Home Moldy Home
If I was building a new home, the last thing that I would want to find out at the last minute is that it has been being built with moldy building materials. This happens a lot more often and is a lot more serious than you might think that it is. Mold is a big problem in homes these days, either due to not paying attention to the condition of your home while you are living in it, due to a natural disaster such as a hurricane, or perhaps the most avoidable reason, it was built into the home that you currently live in.
Mold gets built into brand new homes all the time and it is not only the contractor’s fault, but also the owner’s for not paying attention to the building materials being used at the time. For someone paying to have the home built, what they need to do to help prevent this is to pay attention to what is going on at the building site and to visit it often. The building should be completely covered with a tarp until the walls and roof are totally finished and there is no possibility for rain, snow, or any other kind of precipitation to get into the house.
Before building begins you should inspect all the building materials such as the lumber, sheetrock, insulation, and etcetera that are being used. Inspect them and if you see any signs of mold at all, have them tested with a home test kit and set them aside until you are sure that they are not contaminated.
Something just as important as the other things mentioned here is to make sure your contractor and his or her workers are not storing the building materials directly on the ground. This is just asking for mold to start growing on these and this is completely avoidable by just raising the materials up off the ground. They should come into contact with the soil as little as possible, if at all.
Mold testing during different stages of the home’s development should also take place. The testing should be in the beginning, near the middle, and after the home is completed.
As long as you pay attention to what is going on around the new site of your home while your contractor is working on it, you should be able to almost completely avoid mold being built into your home.
Jim Corkern is a writer and promoter of quality
flood water damage restoration chicago and other states such as
South Carolina mold remediation companies across the united states.
Mold gets built into brand new homes all the time and it is not only the contractor’s fault, but also the owner’s for not paying attention to the building materials being used at the time. For someone paying to have the home built, what they need to do to help prevent this is to pay attention to what is going on at the building site and to visit it often. The building should be completely covered with a tarp until the walls and roof are totally finished and there is no possibility for rain, snow, or any other kind of precipitation to get into the house.
Before building begins you should inspect all the building materials such as the lumber, sheetrock, insulation, and etcetera that are being used. Inspect them and if you see any signs of mold at all, have them tested with a home test kit and set them aside until you are sure that they are not contaminated.
Something just as important as the other things mentioned here is to make sure your contractor and his or her workers are not storing the building materials directly on the ground. This is just asking for mold to start growing on these and this is completely avoidable by just raising the materials up off the ground. They should come into contact with the soil as little as possible, if at all.
Mold testing during different stages of the home’s development should also take place. The testing should be in the beginning, near the middle, and after the home is completed.
As long as you pay attention to what is going on around the new site of your home while your contractor is working on it, you should be able to almost completely avoid mold being built into your home.
Jim Corkern is a writer and promoter of quality
flood water damage restoration chicago and other states such as
South Carolina mold remediation companies across the united states.
Cleaning Moldy Fabric
Sometimes we look into the backs of our closets while we are cleaning them out and we discover an old article of clothing with a fuzzy substance all over it. If you find something like this in the back of your closet, the best thing to do is drop it immediately and go wash your hands. What you were handling was a piece of clothing that has been contaminated with mold and it has been advised to not touch mold spores with your bare hands. This can possibly cause an allergic reaction or just some skin rashes, but either way, there will probably be consequences to deal with.
Most items of clothing that are contaminated with mold can be cleaned and the mold done away with, but most of the time the mold ends up leaving stains. Using bleach to remove the stains can be effective if you are dealing with mold on white clothing, but this is not always the case and chlorine bleach is not effective in killing molds on porous surfaces. You can use a brush to remove the majority of the mold and put a pre-wash spray on it; allow this to soak for about 45 minutes and put it through the washing machine. After this, allow them to dry outside naturally in the sun. Using an artificial source of heat to dry the clothes can set the stain deeper into the fabric and if you are dealing with white clothing, the sun can actually help to bleach the fabric further.
If you are looking to remove the mold and mold stains from something that was made with real leather, you are probably not going to have any luck. Items made out of leather become discolored very easily and mold does a good job of this. They cannot usually be restored after coming into contact with mold.
You can clean off upholstery or curtains that have come into contact with mold using the same method described above and one of the best purchases you can make to keep your home mold free is a vacuum that has a HEPA filter in it. Use this vacuum and its brush attachment to suck up all the mold and its spores; the filter will make sure that the spores are not re-released into the air in your home after being collected.
Jim Corkern is a writer and promoter of quality
North Carolina Sewage Damage Cleanup and other states such as
South Carolina mold remediation companies across the united states.
Most items of clothing that are contaminated with mold can be cleaned and the mold done away with, but most of the time the mold ends up leaving stains. Using bleach to remove the stains can be effective if you are dealing with mold on white clothing, but this is not always the case and chlorine bleach is not effective in killing molds on porous surfaces. You can use a brush to remove the majority of the mold and put a pre-wash spray on it; allow this to soak for about 45 minutes and put it through the washing machine. After this, allow them to dry outside naturally in the sun. Using an artificial source of heat to dry the clothes can set the stain deeper into the fabric and if you are dealing with white clothing, the sun can actually help to bleach the fabric further.
If you are looking to remove the mold and mold stains from something that was made with real leather, you are probably not going to have any luck. Items made out of leather become discolored very easily and mold does a good job of this. They cannot usually be restored after coming into contact with mold.
You can clean off upholstery or curtains that have come into contact with mold using the same method described above and one of the best purchases you can make to keep your home mold free is a vacuum that has a HEPA filter in it. Use this vacuum and its brush attachment to suck up all the mold and its spores; the filter will make sure that the spores are not re-released into the air in your home after being collected.
Jim Corkern is a writer and promoter of quality
North Carolina Sewage Damage Cleanup and other states such as
South Carolina mold remediation companies across the united states.
Some Tips on How to Stop Water Damage
Everyone who owns or rents a home should know what to do to prevent water damage. Even if you rent the property that you’re on, it’s in your best interest to take some responsibility for your living space and do what you can do stop water damage, especially if you plan on renting there for a long time.
If you have a washing machine in your home or apartment, it’s a good idea to make sure that the hose doesn’t have any cracks in it. If the hose ruptures and begins to spew water, it won’t be long before your entire laundry room floor is covered in water and starts leaking into the next room. Hoses that connect to your washer should be replaced as many times and as frequently as you need to, but under normal conditions, every three to five years is sufficient.
A leaky water heater is also a cause of water damage in the home and one of the best ways to determine if you have a leaky one is to look for rust or signs that it has leaked in the past. If a water heater is located on a 2nd or higher floor of the home or apartment building, it needs to be installed inside a pan that has a drain connected to a drain in the floor to make sure the water goes into the plumbing system.
Making sure that water is escaping from your roof the way it should be one of the first things on your mind if you want to prevent water damage to your attic and the rest of your house. If you’re just renting an apartment, then this part is mostly up to your landlord or the property manager. If you’re renting a home, then part of this is probably up to you. Cleaning out the gutters and the general maintenance of the property is up to you unless it’s something serious. Making sure the downspouts that are attached to the corners of the house are free of leaves and other debris will drain water away from the foundation of the house and keep it from sinking into the ground. Keeping water draining away from the house and making sure the cracks around your doors and windows are thoroughly caulked and sealed is another step that you can take to keep water from leaking into your home.
Jim Corkern is a writer and promoter of quality
flood water damage restoration chicago and other states such as
New Jersey mold remediation contractor companies across the united states.
If you have a washing machine in your home or apartment, it’s a good idea to make sure that the hose doesn’t have any cracks in it. If the hose ruptures and begins to spew water, it won’t be long before your entire laundry room floor is covered in water and starts leaking into the next room. Hoses that connect to your washer should be replaced as many times and as frequently as you need to, but under normal conditions, every three to five years is sufficient.
A leaky water heater is also a cause of water damage in the home and one of the best ways to determine if you have a leaky one is to look for rust or signs that it has leaked in the past. If a water heater is located on a 2nd or higher floor of the home or apartment building, it needs to be installed inside a pan that has a drain connected to a drain in the floor to make sure the water goes into the plumbing system.
Making sure that water is escaping from your roof the way it should be one of the first things on your mind if you want to prevent water damage to your attic and the rest of your house. If you’re just renting an apartment, then this part is mostly up to your landlord or the property manager. If you’re renting a home, then part of this is probably up to you. Cleaning out the gutters and the general maintenance of the property is up to you unless it’s something serious. Making sure the downspouts that are attached to the corners of the house are free of leaves and other debris will drain water away from the foundation of the house and keep it from sinking into the ground. Keeping water draining away from the house and making sure the cracks around your doors and windows are thoroughly caulked and sealed is another step that you can take to keep water from leaking into your home.
Jim Corkern is a writer and promoter of quality
flood water damage restoration chicago and other states such as
New Jersey mold remediation contractor companies across the united states.
Preventing Mold From Invading Your Home’s Construction
One of the worst things that can happen to someone who’s building a brand new home is discovering after the construction is completed that mold has been growing within his new haven. It is indeed a problem and it might be more common than you would think.
Mold can and does get built into new homes and a lot of the time, it’s the fault of the contractor for not properly inspecting or storing his building materials and by allowing the site to get wet from rain before the roof and walls are completed. Sometimes what is supposed to be the interior of the home is left uncovered and when it rains, the building materials get soaked and are allowed to dry this way. In warm, humid weather, this can allow mold to get a grip on the structure and begin to grow. You’ll not only have the possibility of mold, but you’ll also put your home at risk of water damage. Covering the building site with tarps or plastic sheeting should keep the rain, snow, (and the mold) out.
You should make sure that the contractor and his/her workers are using good quality materials to build your new home with. Testing the building materials for mold is one thing that you can do to make certain that it stays out of your home’s foundation. If you go to the building site and you see building materials like wood and sheetrock being stored directly on the ground, tell your contractor that they need to be raised up to aid in the prevention of mold growth. Your contractor should already know this, but irresponsible ones or those that are trying to make the process as easy as possible are the ones that you should worry about. Check your contractor’s references and make sure they’ve done a good job for others in the past.
The home should also be periodically checked for mold as it’s being built and after the building is completed. No one wants to go to the trouble of building a home that will be worth quite a lot of money if it’s only going to have to be gutted to remove mold a few months later, right?
If you’re careful and you keep an eye on your home’s construction, you can prevent most kinds of mold and water damage. If you’re not, you’re asking for quite a headache and the loss of a lot of funds.
Jim Corkern is a writer and promoter of quality
Connecticut water damage restoration contractors and other states such as
North Carolina mold remediation contractor companies across the united states.
Mold can and does get built into new homes and a lot of the time, it’s the fault of the contractor for not properly inspecting or storing his building materials and by allowing the site to get wet from rain before the roof and walls are completed. Sometimes what is supposed to be the interior of the home is left uncovered and when it rains, the building materials get soaked and are allowed to dry this way. In warm, humid weather, this can allow mold to get a grip on the structure and begin to grow. You’ll not only have the possibility of mold, but you’ll also put your home at risk of water damage. Covering the building site with tarps or plastic sheeting should keep the rain, snow, (and the mold) out.
You should make sure that the contractor and his/her workers are using good quality materials to build your new home with. Testing the building materials for mold is one thing that you can do to make certain that it stays out of your home’s foundation. If you go to the building site and you see building materials like wood and sheetrock being stored directly on the ground, tell your contractor that they need to be raised up to aid in the prevention of mold growth. Your contractor should already know this, but irresponsible ones or those that are trying to make the process as easy as possible are the ones that you should worry about. Check your contractor’s references and make sure they’ve done a good job for others in the past.
The home should also be periodically checked for mold as it’s being built and after the building is completed. No one wants to go to the trouble of building a home that will be worth quite a lot of money if it’s only going to have to be gutted to remove mold a few months later, right?
If you’re careful and you keep an eye on your home’s construction, you can prevent most kinds of mold and water damage. If you’re not, you’re asking for quite a headache and the loss of a lot of funds.
Jim Corkern is a writer and promoter of quality
Connecticut water damage restoration contractors and other states such as
North Carolina mold remediation contractor companies across the united states.
Preventing Mold From Invading Your Home’s Construction
One of the worst things that can happen to someone who’s building a brand new home is discovering after the construction is completed that mold has been growing within his new haven. It is indeed a problem and it might be more common than you would think.
Mold can and does get built into new homes and a lot of the time, it’s the fault of the contractor for not properly inspecting or storing his building materials and by allowing the site to get wet from rain before the roof and walls are completed. Sometimes what is supposed to be the interior of the home is left uncovered and when it rains, the building materials get soaked and are allowed to dry this way. In warm, humid weather, this can allow mold to get a grip on the structure and begin to grow. You’ll not only have the possibility of mold, but you’ll also put your home at risk of water damage. Covering the building site with tarps or plastic sheeting should keep the rain, snow, (and the mold) out.
You should make sure that the contractor and his/her workers are using good quality materials to build your new home with. Testing the building materials for mold is one thing that you can do to make certain that it stays out of your home’s foundation. If you go to the building site and you see building materials like wood and sheetrock being stored directly on the ground, tell your contractor that they need to be raised up to aid in the prevention of mold growth. Your contractor should already know this, but irresponsible ones or those that are trying to make the process as easy as possible are the ones that you should worry about. Check your contractor’s references and make sure they’ve done a good job for others in the past.
The home should also be periodically checked for mold as it’s being built and after the building is completed. No one wants to go to the trouble of building a home that will be worth quite a lot of money if it’s only going to have to be gutted to remove mold a few months later, right?
If you’re careful and you keep an eye on your home’s construction, you can prevent most kinds of mold and water damage. If you’re not, you’re asking for quite a headache and the loss of a lot of funds.
Jim Corkern is a writer and promoter of quality
Connecticut water damage restoration contractors and other states such as
North Carolina mold remediation contractor companies across the united states.
Mold can and does get built into new homes and a lot of the time, it’s the fault of the contractor for not properly inspecting or storing his building materials and by allowing the site to get wet from rain before the roof and walls are completed. Sometimes what is supposed to be the interior of the home is left uncovered and when it rains, the building materials get soaked and are allowed to dry this way. In warm, humid weather, this can allow mold to get a grip on the structure and begin to grow. You’ll not only have the possibility of mold, but you’ll also put your home at risk of water damage. Covering the building site with tarps or plastic sheeting should keep the rain, snow, (and the mold) out.
You should make sure that the contractor and his/her workers are using good quality materials to build your new home with. Testing the building materials for mold is one thing that you can do to make certain that it stays out of your home’s foundation. If you go to the building site and you see building materials like wood and sheetrock being stored directly on the ground, tell your contractor that they need to be raised up to aid in the prevention of mold growth. Your contractor should already know this, but irresponsible ones or those that are trying to make the process as easy as possible are the ones that you should worry about. Check your contractor’s references and make sure they’ve done a good job for others in the past.
The home should also be periodically checked for mold as it’s being built and after the building is completed. No one wants to go to the trouble of building a home that will be worth quite a lot of money if it’s only going to have to be gutted to remove mold a few months later, right?
If you’re careful and you keep an eye on your home’s construction, you can prevent most kinds of mold and water damage. If you’re not, you’re asking for quite a headache and the loss of a lot of funds.
Jim Corkern is a writer and promoter of quality
Connecticut water damage restoration contractors and other states such as
North Carolina mold remediation contractor companies across the united states.
Subscribe to:
Posts (Atom)
